TPMS reset and EGR Reset Battery registration Injector Coding(IQA) Electrical Park Brake(EPB) reset Reset PCM KAM Throttle Position Sensor(TPS) reset ABS Service Bleed and Oil service reset Steering Angle Sensor(SAS) calibration Diesel Particulate Filter(DPF) Regeneration Fuel Injection Pump Learn Basic functions for Ford Group Vehicles Diagnosis Engine System Diagnosis SRS(Airbag) Diagnosis ABS Diagnosis and TPMS Diagnosis Transmission System Diagnosis SAS Diagnosis & ESP System Diagnosis Battery System Diagnosis and Battery Test Function Immobilizer System Diagnosis & Fuel Pump Diagnosis abs ABS Bleeding for Ford Group Vehicles Diagnosis The diagnostic tool can read and clear the ABS sensor error code and turn the warning light off. It supports ABS Bleeding. You can make a determination of what could be the causes of the error: low brake fluid, a blown fuse, or abnormal signals from wheel sensors. OIL Oil Service Reset for Ford Group Vehicles Diagnosis When you want to reset your oil service after you changing the oil or simply want to reset your vehicle inspection warning light(please make sure your vehicle is in well condition), this is the device you need. It allows you to reset the service lamps on the instrument cluster. SAS Steering Angle Sensor Calibration You can use FD700 to read the fault codes, perform the sensor calibration if needed, and clear the codes when you done. Note: 1. Set the steering wheel to the center point and align the front wheels straight ahead before you do the SAS reset. 2. If the SAS MIL light illuminates on the dashboard after you reset the SAS and the codes can't be cleared, then you need to turn the ignition on, pulling the wheel as followed: it's left end, it's right end and then back to the center point. epb Electrical Park Brake (EPB) Reset for Ford Group Vehicles Diagnosis EPB(Electrical Parking Brake) is a technology that realizes parking brake by electronic control. FD700 is a essential tool required to release rear electric parking brake unit when replacing rear pads or discs so that the caliper piston can be moved back. It can also clear codes and turn off the EPB light when it’s done. Advanced functions for Ford Group Vehicles Diagnosis TPMS TPMS Reset for Ford Group Vehicles Diagnosis If the TPMS (Tire Pressure Monitoring System) light is illuminated, it means your tires could be underinflated, which can lead to undue tire wear and possible tire failure. FD700 car code reader can read and clear TPMS error codes and turn off the TPMS warning light after you replace the tire. BATTERY REGUSTRATION Battery Registration for Ford Group Vehicles Diagnosis Disregarding the need to register and code for a new battery may result in improper charging. FD700 can help you register a new battery once you replace it. Note: 1. Not all vehicles need to do the battery reset after changing batteries. 2.If the parameters of the new battery are inconsistent with the old battery or the parameters are too different, registration may fail. PCM PCM Special Engine Functions (DPF Regeneration, IQA, TPS Adjustment Included) for Ford Group Vehicles Diagnosis DPF Regeneration and Reset, TPS Reset, Injector Coding(IQA), Exhaust Gas Recycling etc. Note: Different car model might use different engine model, the specific reset functions may vary. 6 ALL SYSTEM DIAGNOSIS FOR FORD GROUP VEHICLES The ANCEL FD700 works on most OBD2 vehicles sold in the US after 1996 and OBD2 16PIN Ford Group vehicles(Ford, Lincoln, Mercury) after 1996. Please note: 1. Each car model has different system configurations, the specific reset functions may vary. 2. The update software only supports Windows 7/8/10. Only Windows 7 needs to install the driver before updating the device. 3. It can do the all system diagnosis and special functions for FORD group vehicles. But FD700 only can diagnose engine system for 16 pin Non-FORD vehicles sold in the US after 1996. Features & details The FD700 OBD2 scanner is specially designed for diagnosing most 12V 16-Pin FORD/LINCOLN/MERCURY Ford Series vehicles(after 1996), but it also has the ability to work on 12V cars and light trucks (non-electric) manufactured in 1996 or later that are OBD II-compliant with 16-Pin OBD II protocols (J1850 VPM, J1850PWM, ISO9141, KWP 2000 and CAN). OBD 6 modes for OBD II vehicles, FD700 is capable of reading/erasing, showing error code definitions, turning off the MIL (check engine light), reading data stream, testing EVAP system, reading I/M and retrieving VIN information. Basic functions for FORD Group vehicles: it can do the all system diagnosis(ABS, Transmission, SAS, SRS, ESP, TPMS and other systems). Please note that FD700 only can diagnose engine system for 16 pin Non-FORD vehicles sold in the US after 1996. But it can do more systems and special functions for FORD vehicles. Special functions for FORD Group vehicles: ABS Service Bleed, Battery registration, EPB Maintenance, SAS Calibration, Reset the EGR Valve Learned Values , Reset TCM KAM, PCM engine special functions, Fuel Injection Pump Learning, Transmission Learning, TPMS reset, etc. Automatic vehicle model identification makes it easy to use. Two color UI themes for you to choose. Life-time free software updates available to fix the latest bugs or add new parameters. Just download the software from the official website, then follow on-screen instructions to install.